Comments on: +9V to 60V PWM 2.3A Solenoid Valve Driver using DRV101 https://www.electronics-lab.com/project/9v-to-60v-pwm-2-3a-solenoid-valve-driver-using-drv101/ Open Source Hardware Electronics Projects Mon, 01 May 2023 09:18:51 +0000 hourly 1 By: A.Maneesha Rani https://www.electronics-lab.com/project/9v-to-60v-pwm-2-3a-solenoid-valve-driver-using-drv101/comment-page-1/#comment-402722 Mon, 01 May 2023 09:18:51 +0000 https://www.electronics-lab.com/?post_type=project&p=63564#comment-402722 Hello,
I need a driver circuit with the following specifications
The following are driver circuit design requirements for generating a DC pulse

  • ON time: 30-100ms 
  • Voltage: 60V DC
  • current rating: 8A
  • off time: 20sec

can you please suggest any driver circuit available with the above-mentioned parameters

]]> By: mixos https://www.electronics-lab.com/project/9v-to-60v-pwm-2-3a-solenoid-valve-driver-using-drv101/comment-page-1/#comment-394776 Thu, 15 Oct 2020 14:27:55 +0000 https://www.electronics-lab.com/?post_type=project&p=63564#comment-394776 In reply to Luis M. Mendoza S..

Glad you found what you were looking for. This can work as standalone driver as it produce the necessary signal to drive the solenoid.

]]> By: Luis M. Mendoza S. https://www.electronics-lab.com/project/9v-to-60v-pwm-2-3a-solenoid-valve-driver-using-drv101/comment-page-1/#comment-394775 Thu, 15 Oct 2020 08:07:31 +0000 https://www.electronics-lab.com/?post_type=project&p=63564#comment-394775 Do not consider my previous question. I found the module DRV101 version (2.3 A) Can I connect the driver to the Arduino or works without a microprocessor?

]]> By: mixos https://www.electronics-lab.com/project/9v-to-60v-pwm-2-3a-solenoid-valve-driver-using-drv101/comment-page-1/#comment-271815 Thu, 13 Feb 2020 17:07:14 +0000 https://www.electronics-lab.com/?post_type=project&p=63564#comment-271815 The minimum input voltage for this board is +9V, i am not sure if you can make it work with 6V solenoid.

]]> By: Matej Oder https://www.electronics-lab.com/project/9v-to-60v-pwm-2-3a-solenoid-valve-driver-using-drv101/comment-page-1/#comment-271216 Wed, 12 Feb 2020 12:22:18 +0000 https://www.electronics-lab.com/?post_type=project&p=63564#comment-271216 In reply to mixos.

ow okay i think that i control how much to be open with my arduino with out turning him off
how can i get voltage down to 6V because i have 6V dc valve in use right now

]]> By: mixos https://www.electronics-lab.com/project/9v-to-60v-pwm-2-3a-solenoid-valve-driver-using-drv101/comment-page-1/#comment-271214 Wed, 12 Feb 2020 12:20:10 +0000 https://www.electronics-lab.com/?post_type=project&p=63564#comment-271214 In reply to Matej Oder.

Right, you can’t control the valve opening, it’s just ON/OFF

]]>